Translate

Saturday, April 7, 2018

Gargoyle Whirligig or Weathervane

Gargoyle Whirligig or Weathervane

This is a concept idea and not intended as a pattern or plan. It has not been tested and may not work as suggested and further modifications may be required to make it work. The concept is to create a whirligig or weathervane with a gargoyle chasing or playing with a metal sphere.  Do not use metal disc for the propeller as they may fly off in high winds becoming a hazard. Instead we recommend using metallic paint on wood. Do not for get to angle the propeller blades so they catch the wind. If the propeller does not catch enough wind, a different design may have to be used such as mounting the gargoyle and propeller above the horizontal pivot.
(Note) the difference between a whirligig and a weathervane is that a weathervane only shows the direction of the wind, whereas a whirligig has moving parts powered by a propeller,or may also consist of just a propeller.

Please be sure and checkout our other blogs and web site for crafting ideas.

Friday, April 6, 2018

Flying Dragon whirligig

Flying Dragon whirligig concept

           This is a concept idea and not intended as a pattern or plan. It has not been tested and may not work as suggested and further modifications may be required to make it work. The concept is to attach the wings to the dragon’s body with hinges of some type and then attach metal rods to the outer edges of the wings. The opposite ends of the metal rods would have some type of bead attached to the end so that it could freely ride an offset wheel which would be turned by a propeller. As the wheel turns it rises and falls lifting and lowering the dragons wings.

Please be sure and checkout our other blogs and web site for crafting ideas.

Thursday, April 5, 2018

Goldfish Whirligig


This is a concept idea and not intended to be a pattern. The design is not done to scale and has not been tested.  There are a number of ways this concept could be used and the number of fish is only limited to how long or how much space you have on the whirligig. The concept is intended to show how a wire crank shaft might be used. The propeller may have to be scaled up in order to get enough power to turn the crank and the propeller it’s self could be designed with goldfish at the ends of the propellers blades. Be sure to use washers and nut on crank shaft to keep shaft in place as it turns.
Thank you for checking us out.
Be sure to check out our other sites for more crafting ideas.

Wednesday, April 4, 2018

Mandala Pattern Illusion Whirligig




As I have stated before this is a concept idea only, not a pattern. It is a design that creates the illusion of dots that change color and makes a great kinetic art deco for the yard.

Monday, April 2, 2018

UFO Solar Whirligig Idea

Sometimes all you need is a good idea.

            I had seen these globe shaped solar lights and used them in may other projects and after watching a great sci-fi movie realized they could be used to make a UFO. 
I began by cutting a circle out of a 2 x 6 scrap wood on my band saw, but I think I will use 1" of or thinner wood stock next time and glue pieces together as the thick cuts were somewhat difficult.
Dividing the circle in half with a pencil line.
And then using a belt sander I began beveling the top and bottom edges into a flying saucer shape.

I drilled a hole for the solar light to fit in and carved with the Dremel tool a recess for the solar light set in,
so it would sit flush is in the following photo.

Then using 2 x 2's created the pivot and vein part to mount the UFO on top of.
I used a screw that had no upper threads in the vertical mount, cut off the head, and using a drama rounded the top of the screw.

On the horizontal pivot I placed a brass tube in a hole I drilled slightly off center and then placed a BB in the tube to act as a bearing.
So I had something that looked like the following. 


I took a plastic florescent tube covering and cut a short piece to cover the black shaft of the solar light.
I painted the black shaft of the UFO solar light with florescent green paint and the inside of the clear tube with glitter.


Cannibalizing a second regular solar light, I used a Dremel saw blade to cut solar light carefully apart without disconnecting any wires. I cut a channel in the horizontal 2 x 2 and fitted the solar cell there and mounted the rest of the components(LED, battery) under the clear tube. But I found this to be too bright and later painted the inside of the tube with more florescent green paint to dull the brightness of the light.


I will later mount some type of tail fin and cow being abducted as a counterbalance to the UFO.
 As you can see I'm still not quite getting the effect that I wanted and in a future design I will most likely use cascading LEDs for the tractor beam at the bottom of the UFO.
So far the project has gone well and I will update this post when it is completed.






Not sure which one I like, so posted both. UFO on the back side is just a tail fin cutout to act as rudder in the wind. Cow is also just a cutout 1/8" stock or thicker. A propeller could aslo be added to lighted end.











Thursday, July 20, 2017

Who's catching who - Fisherman and giant fish whirligig

Who's catching who - Fisherman and giant fish whirligig


    In this whirligig concept we used an optional second pivot. Depending on pivot placement, boat shape, ect boat should wobble back and forth giving the impression the fisherman is fighting the fish.
    Unlike previous designs the bottom pivot is set directly in the fish and there is no need for a runner board or a tail fin. You do however need to make sure that the fish is cut out of 6/8" or thicker wood stock so it can handle the stress of the pivot.
    There is a small optional propeller at the aft end of the boat. The boat motors is actually part of the boat for added strength when adding the propeller.
    As always, keep in mind, this is only a concept design and has not been prototyped or tested. Adjustments in the locations of pivots and and types of materials used may have to be made.
Other considerations that need to be made are what types of weather the whirligig or weathervane will be exposed to. When designing a whirligig for areas like Nevada, smaller propellers may be preferable because of gusty high winds. Whereas along the coast where you're more apt to have constant steady breezes, larger propellers may be incorporated.
    I hope that this concept design inspires you to create your own designs. For more concept and patterns please be sure and check out our website at www.nevadacrafter.com

Also be sure to check out our following blogs for money making craft ideas.
https://craft44.blogspot.com/

https://nevadacrafter.blogspot.com/

Saturday, July 15, 2017

Double Pivot Bumble Bee Whirligig / Weathervane

Double Pivot Bumble Bee Whirligig / Weathervane  

As with any double pivot system, the location of the pivot determines how much action or how little action in the pivot takes place. Moving the pivot for the bumblebee forward or back will determine how much back and forth movement the bumblebee makes. If the pivot is placed in the middle of the bumblebee, the bumblebee will have a tendency to spin. You will also want to take into consideration that the bumblebee needs to clear the tail fin as it moves back and forth.
     The legs and antennae are made from wire and the eye can be a simple bicycle reflector. Tail fin can also be reflectors, cutouts, wood burned etching, or simply painted design. Of course as always the design can be scaled up or down depending on size whirligig that you need.  The bumblebee propeller wings are small, which is indicative of a bumblebee which has disproportionate wings to body size. The black body and orange stripes are whatever size and width that you desire.
    The overall design is a basic double pivot whirligig/weathervane. The concept can be used on any design or theme. I hope you enjoy this design concept, feel free to give positive creative feedback.
Always be sure to check out our website www.nevadacrafter.com as well as our other blogs.

Blog links
https://craft44.blogspot.com/

https://nevadacrafter.blogspot.com/

Have a great time crafting and thank you for checking us out.

Wednesday, February 22, 2017

Shooting Star whirligig sign

Do you need to hitch your sign to a shooting star?



Once again keep in mind this is a basic concept design by Nevada crafter.com it is not done to scale and has not been tested. 

     In this design we have made it so that you can cut the design from a single piece of 1/2"plywood. The rainbow part of the sign is seven color bands. This is so you can have your chakra colors if you're into the yoga chakra colors. 
    It should also be noted that if you would like to hang additional signage below the sign you can do so.

    One of the things that we have changed is the propellers are not the traditional shape and they have stars cut out of the blade. Now this does affect the efficiency of the whirligig propeller but should not affect its basic function so long as the blades are mounted at opposing angles. 

    So if this post is to your liking please be sure to checkout our other blogs and our website.


3-D pen ideas

Nevada crafter blog

craft 44

And our web site Nevadacrafter.com

Monday, January 16, 2017

Basic Pivot for Whirligig or Weathervane

Basic Pivot for Whirligig or Weathervane

    In this post I wanted to go into more detail about the whirligig or weathervane pivot and how it is put together. The diagram below is intended as a basic guide and can be adjusted in size or scale according to the size whirligig or weathervane that you're creating. 

    For basic demonstration purposes this is a basic 12 inch pivot for whirligig or weathervane. Were using a heavy screw with threads that only go halfway up and a non-tapered shaft. The type of screw head does not matter as it will be cut off once the screw is installed in the vertical mounting board. Screw the screw into the vertical mounting board just enough to cover the threats. Making sure to keep shaft of screw vertical. It may be necessary to drill a pilot hole to help keep the screw straight, as this is what your project is going to pivot on. This should leave the upper half of the screw without threats exposed. Then using a Dremel tool (with appropriate safety goggles and other protective equipment) use a cutoff blade to cut off the screw head and a grinding bit to either round the top of the screw shaft or grind a concave dimple. Once you've completed your vertical board with pivot it is time to create the horizontal part of your pivot. 
    One of the important things to take in consideration before drilling a hole is the metal or plastic sleeve that will fit inside the hole. The metal or plastic sleeve should fit tightly in the hole but the screw should fit closely but not so tight as to inhibit the upper part of the pivot from rotating. Any wobbling in the rotation of the upper pivot will simply create excessive wear and erratic movements.
    At the bottom of the hole place a 1/4" hunting shot (slingshot ammo found in the sporting good section) or a small ball bearing, or BB depending on the size hole being used for the vertical shaft. The basic reason for placing the metal ball at the bottom of the hole is to prevent metal rubbing against wood and to reduce friction as the upper pivot rotates. Using a metal ball that is slightly larger than the metal or plastic sleeve and then placing the metal sleeve on top of the metal ball in the hole will help keep the metal ball in place.
     Using wood stock that is approximately 1/2" X 1/2" X 12" long measure 3 inches from one end and drill a hole.  Where you position the whole will depend on how you want the pivot to react to the wind. The closer you position the hole to the center, the more erratic the pivot will act. The closer to the end you position the whole the greater the force that will be applied not only to the pivot reacting to the wind, but also to the pivot itself. I have found that a quarter of the total distance gives a good balance to the pivot and does not put excessive strain on the pivot. 
    Once you have the metal ball and sleeve in place the two parts to the pivot should be ready to go together. You can put a small amount of graphite lubricant at the bottom of the hole before you put the two together. 

There you have it a basic pivot to mount your whirligig or weathervane on. For this and other ideas please be sure and check out our website www.nevadacrafter.com and our blog's at http://craft44.blogspot.com/ and http://nevadacrafter.blogspot.com/ and http://3dpenideas.blogspot.com/
    If you have any questions please be sure and post those questions to the blog and I will try to answer them as promptly as I can.

Friday, January 13, 2017

Spacewalking astronaut and space capsule weathervane

Spacewalking astronaut and space capsule weathervane


   So the idea or concept was to create an astronaut walking in space. At first the design seemed to be simple, but as I researched it more I quickly realized that I could take the design to whatever level of detail that I wanted. For presentation purposes I have chosen a simpler design than what an actual astronaut and space capsule would look like. It may be possible to create lifelike replicas but as this project would be exposed to the elements I chose to keep it simple. This way if the weathervane should become damaged it would be easy to make repairs. 
    I chose a weathervane design to minimize moving parts but also decided to add what is referred to as a wobble effect. This is done by adding a part of the design to a spring, metal band, or spring wire. In this case I'm using spring steel wire as the astronauts tether. The bouncing around motion that the astronaut will give in the wind will add to the illusion of someone actually walking in space. 
    The space capsule is actually cut out of 1/2" wood stock and the lower flame is notched so as to fit over the side part of the pivot. The thicker Woodstock allows you to make a more secure attachment to the pivot and the overlapping flame at the bottom will give it a more three-dimensional appearance. It should also be noted that I have intentionally left off the country of origin insignia on the side of the space capsule. This is so that you can put your own insignia on the side of the space capsule such as an American flag or some other countries insignia. 
    The pivot itself is a basic design and you can refer to the pivot design at the bottom of the following post. windmillhorses-weathervane-whirligig 


For this and other great ideas be sure and check out our website www.nevadacrafter.com
and some of our other blogs such as
http://craft44.blogspot.com/
and
http://nevadacrafter.blogspot.com/


Tuesday, January 3, 2017

Lubricating whirligigs and other mechanical projects

Lubricating a whirligig or mechanical project with moving parts.

    Lubricating whirligigs or mechanical projects can be a challenge. The materials you work with can vary from metal to wood and even plastic. Add to this a project that is exposed to the outdoor elements, wind, rain, dust, dirt and even the unexpected squirrel.
    The basic challenge is to keep moving parts moving and there are a few basic rules that you need to consider when you're creating mechanical art.
    The first rule of thumb that I was taught long ago, is to always try and work with like materials. Putting a moving metal part against a wooden part will always result in the wooden part eventually being worn away. Putting plastic or nylon parts in between will help lengthen the life span of your mechanical wonder, but will have to be periodically replaced. And always try to keep lubricated parts sealed when possible. Always use washers and spacers when possible to keep metal parts from rubbing against wooden parts. 
    As for the lubricants themselves, my go to lubricant has always been a pencil. The graphite used to make the pencil lead makes a perfect lubricant. Rubbing a pencil lead on a propeller shaft works wonders and is resistant to most weather conditions. Liquid graphite can also be used when you have metal to metal surfaces, such as brass tubing and brass welding rods used for propeller shafts or other metal to metal parts. 
    As you're creating these projects you should always keep in mind to create projects that can be disassembled. This will make it easy for the owner not only to periodically lubricate moving parts but also make any repairs or replace any worn parts that need replacing. Another option is to also include in your projects lubricating holes, as shown in the diagram above. These are holes or tubing that allow you to lubricate the moving part without disassembling and are usually mounted on the bottom side prevent collecting dust or water. 
    White lithium grease is also an optional lubricant. Normally used on bike chains and other outdoor moving parts such as door hinges. It also is extremely weather resistant and has the added advantage of being in a spray form. 
    The next lubricant is actually a solid and usually in the form of nylon washers. But as I have found over the years nylon washers and metal bearings can be very expensive to use. Using crazy straws and washers cut from milk jugs will work but keep in mind most plastics are designed to be biodegradable and may not last very long if exposed to sunlight. Crazy straws dipped in a pot of boiling water will immediately straighten and as long as they are cut to length and hidden inside the whirligig or project they will last quite a long time. Add some graphite lubricant and they will undoubtedly outperform most expectations. Also keep in mind when using plastic or even brass tubing you will want to keep the sizes close fitting. A loose moving part will wear much faster.
   
    I hope these tips on lubricating your mechanical art are of help. Please be sure and visit our website www.nevadacrafter.com for more tips and ideas on your next craft project.

Thursday, December 22, 2016

Dragon shelf bracket with hook

Dragon shelf bracket with hook

So this is a different take on the previous shelf bracket concept. The basic shelf bracket can be adapted to just about any theme. Using a scroll saw you can cut out just about any character for that one-of-a-kind bookshelf. Again I recommend that it be cut out of a material similar to Masonite or plywood that does not have a wood grain. This is so the tail can withstand the extra stress that may be placed on it. If you're only planning to hang lightweight items off of the tail then I would go ahead and use 1/2" or 3/4" wood stock. Again the amount of weight that the hook can withstand greatly depends on how the grains in the wood run. The shelf on top of the bracket will set high enough to protect the horns from being broken off or snagging items on them.
     I created this design for someone I know that loves to read fantasy books and I hope that you will love this design as much as I do. 


Please be sure to check out our web site www.nevadacrafter.com and also http://craft44.blogspot.com/ and http://nevadacrafter.blogspot.com/

Wednesday, December 21, 2016

Shelf bracket with hook

This is a free pattern from Nevadacrafter.com

The following is a free pattern for a shelf bracket with hook.
This pattern is pretty much self-explanatory. The flower design is optional and can be created by either wood-burning, carving or scroll saw.
Brackets are screwed to the wall and to the shelf. The hook gives you a place to hang things such as a purse.
Be sure to use appropriate screws and fasteners. As always the pattern can be adjusted to fit the size of your project. Long shelves should consider using more than just to brackets, if you're looking to hang heavy items from the hook it is recommended that the bracket be cut out of material that does not have wood grains, which can cause weak points in the hook.
For this and other crafting ideas be sure and visit www.nevadacrafter.com

Thursday, October 6, 2016

Spooky Ghost Novelty

    As kids we have all played with magnets and how two like poles such as + and +will repel one another. I have used magnets in many projects since then and in a lot of different ways.
    In this project we are hiding magnets in a friendly looking ghost that hangs from a hangar over a wooden base with another hidden magnet in the base. We make sure that each magnet repels each other before gluing in place.
    As the ghost swings back and forth over the base, the ghost will move to avoid the magnet or magnets that are in the base. As a result the ghost does not move back and forth as you would think. I like using rare earth magnets because they are stronger and can be smaller and easier to hide. More than one magnet can be placed in the base to give additional and more unpredictable movements, just make sure all the magnets repel one another.
    This is one of my favorite novelties to create during the holidays. It makes a great conversation piece and easily amuses people who are not familiar with magnetism and how it works.

    As always this is a Nevada crafter.com project and has not been tested or created to scale. Adjustments and refinements to the project may be necessary.
It is presented here only as a form of entertainment.

[CAUTION: this project may contain small parts and is not intended for small children as these parts may present a choking hazard] 

Friday, September 23, 2016

Halloween flying bat mobile

Halloween flying bat mobile

 If it is done right it's a pretty cool project. A light tug on the pull string and the bat will appear to be flying. It makes a really cool decoration and center of conversation . The entire project is held together by chords or heavy string and works something like a marionette. NOTE: it should not be hung over a crib and should be kept out of reach of small children as the chords and strings can become a choking hazard!
   First drill your preliminary holes and attach the wings to the body using your chosen cord or string. Making sure that the corridor string you choose is heavy enough to support the weight of the project. Start with a ring or loop at the top, add four strings of equal length. (Length is about 18 to 24 inches )  Run two strings on each side of the bat through slits cut in to the dowel and use a dowel to keep your strings separated. You should now have two strings on each side of the dowel for the wings. The most difficult thing about a project like this is finding the right balance points. Adjusting the weight in the pull cord is usually the easiest but in some cases you may have to move the cord holes that support the bat. The two outer holes can be moved closer to the body if the body is too heavy or move them slightly further out if the wings are too heavy. Before painting and finishing your project it is best to do a trial run with everything assembled temporarily. If it is done correctly it should be balanced as shown above in the small diagram. Holes drilled in the wrong place can be filled in with putty or glue and sawdust. Be sure and take notes of where the correct balance holes are if you intend to make more than one .The body can be sanded down to remove some weight or a thinner wood stock can be used. Basically the body should equal the weight of the two wings. Metal washers can be sandwiched In between two pull cord bats or a thicker one that is hollowed out if extra weight is needed for the body. The pull cord bat is actually optional and should be included with the total body weight if used.
    Once you have your project balanced you can then proceed to paint your project. Keep in mind to use an equal number of coats of paint for both the wings and the body so as not to throw your weights off.
    One of the nice things about this project as it uses a single color paint with only a few highlights as desired. Can use plastic animal eyes to make it more realistic or paint a couple of thumbtacks.

 NOTE: If you want to make a quick trial mobile, it can be made out of cardboard or poster board.

    In the poster board bat I had to move the holes for the wings out further to accommodate the width of the pencil length dowel. I used paperclips on the wings to adjust the balance. This way once I have the weight correctly adjusted I could simply insert the paperclips into the foam part of the wings Instead of using the small bat on the pull cord I used beads as a counterweight. That is so I can add or subtract however many beads I needed to. I also used beads on the underside of the wings to keep the embroidery thread from pulling through.
     The size and type of material will always cause you to make adjustments in the location of the holes, the weights in the wings, and the counterbalance on the belly (pull cord beads). This is why you completely assemble your project. Paint, eyeballs and anything else you add to the project also adds weight.
    Once you have made all your adjustments and have decided on all the materials that you're going to use, it is a good idea to make notes and adjustments to your pattern. That way any copies you build in the future will be simple and easy.

      

    As always it should be noted that this prototype design is the property of Nevada crafter.com it is free to the public to use so long as it is not put into mass production. (Anything over 500) please also note that this post is copyrighted and Nevada crafter does not allow reprint, redistribution or republishing without permission from Nevada crafter.com

Tuesday, August 23, 2016

Cloud rainbow sign with whirligig umbrella - sign is optional

This is a cloud rainbow whirligig umbrella that can be used as a business sign or address sign. The whirligig part of this is unusual in that it is a hanging whirligig. You must make sure to mount the fan blades of the umbrella at an angle for it to work properly. As with many of my other designs, this is a concept design and has not been tested or prototyped as of yet. The design is set up so that you can scale it to whatever size you need. Keep in mind that if you make the whirligig too large it may not work mechanically. The eye screws may have to be mounted differently than shown to offset the weight of the umbrella and rainbow. The left eye screw should probably be on the rainbow above the umbrella. You may also want to scale the umbrella down in size.
    It should also be noted that the umbrella by its self is a whirligig and can be used alone without the cloud and rainbow.

Friday, August 5, 2016

hanging hand whirligig sign

Hanging Hand Whirligig Sign

Signs can be the cornerstone of any business success. Attracting customers attention can sometimes be a daunting task, as you are usually competing with hundreds of other signs.
      One of the main things that I've learned in the 40 years of being in business for myself is that the only thing that gets people's attention is the oddity that stands out from everything else.
    Motion is usually key, as this taps into primitive survival brain functions. The brain cannot ignore such things until it identifies what it is that's moving. 
     I learned very early on that whirligigs make some of the best signs. They don't always scale up to the larger sizes, but because of their motion and uniqueness they don't need to. In many cases people will actually stop and turn around to see what it is. Their curiosity gets the better of them until they know what it's about. That is why smaller signs work well in conjunction with larger signs. The larger sign states the name of the business, the smaller sign acts like a fishing lure directing them to the front door or whatever else you want their attention on. 
    Now with all this said I also learned that after seeing the sign for several months people became accustomed to it and begin to largely ignoring it. It is at this point that I change out the sign entirely and from time to time rotating different signs and maintain their interest and attention. 

Friday, July 29, 2016

Steampunk whirligig / weathervane by Nevada crafter.com

    This is probably the most complicated whirligig design that I have created thus far. And as such I would like to stress that this is an untested design that may be better suited as a decoration indoors rather than an actual functioning whirligig or weathervane.
    The reason for the complexity is that it uses several different materials that are not usually incorporated into a whirligig. The design is a steam punk style and uses everything from wire, tubing and even wiremesh.
    I think it would look really cool using a copper mesh for the netting. The balloon itself is a simple oval 1/4" cut out painted gray to resembled the dirigibles used during the Victorian era. The guide wires or ropes will need to be some type of rigid wire such as brass welding rod or even bicycle spokes to support the balloon. Steam generator in the middle can be part wood but also could be just as easily fashioned out of a metal cut out. Tubing could be substituted with copper or brass wire. The steam gauge itself can be a sliced dowel painted silver and then applying a decal for the gauge and numbers. The ship body is cut out of 1/2" to 5/8" wood stock. The propeller is actually quite simple, in that it is a dowel using beads as a spacer and cap.
    The rest of the design is left open for your own imagination, such as the type and style of anchor that you wish to use or whether you would want to add any ports. I personally thought about drilling a hole in the side and then mounting glass marbles as port windows. You could probably use pipe fittings or even Sculpey clay for copper or brass fittings.

   If you have any suggestions or ideas please feel free to post them in the comment section. I'd be very interested in hearing people's input so I can make improvements on the design or future designs.

Please be sure and check out our website www.nevadacrafter.com and also check out our other blogs.
http://nevadacrafter.blogspot.com/

http://craft44.blogspot.com/

http://3dpenideas.blogspot.com/



Monday, July 25, 2016

Top View Dragonfly

Top View Dragonfly

This is a public domain free to use dragonfly pattern created by Nevada crafter.com 

    This is a basic design that could be used or adapted to just about any project. From woodworking to 3-D pen's this simple design could be turned into anything from a whirligig to a simple stained-glass ornament,
or even a wire framed pendant.
    Basic designs like this are a good starting point and can be added onto with other designs or used simply by itself. 

Monday, July 18, 2016

Seagulls And Fruit Weathervane

Seagulls And Fruit Weathervane

The design can be used with any fruit or object you like and the birds need not be seagulls. It is basically presented to demonstrate a concept that involves using wind drag instead of a tail fin to control the direction of the weathervane. The number of birds is up to you. I recommend that you use spring steal so it does not loose it's shape and will give the birds more action in the wind.